Operator ManualZMKW52212 / 968999660ZMKH52252 / 968999661ZMKH61252 / 968999662ZMKW48172 / 968999730ZMKW48192 / 968999779Please read the operator’s man
English-10SAFETYUse extra care when loading or unloading the • machine into a trailer or truck.Always wear eye protection when operating • machine.Dat
English-11SAFETYPersonal Safety EquipmentMake sure that you have rst aid equipment • close at hand when using the machine.Never use the machine when
English-12SAFETYChildrenTragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machi
English-13SAFETYSafe Handling of GasolineTo avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely am
English-14SAFETYGeneral MaintenanceNever operate machine in a closed area.• Keep all nuts and bolts tight to be sure the • equipment is in safe workin
English-15SAFETYEnsure that nuts and bolts, especially the • fastening bolts for the blade attachments, are properly tightened, torqued and that the e
English-16SAFETYThe blades are sharp and can cause cuts and • gashes. Wrap the blades or use protective gloves when handling them.Check the parking br
English-17SAFETYRoll over Protection system (ROPS)The ROPS increases the basic weight of the unit by 42 lbs/19 kg. The ROPS on the US units are standa
English-18SETUP AND ADJUSTMENTSSetupUncrate machine.ROPS Assembly Components1 - Top loop1 - Left side post1 - Right side post1 - Hardware bag 2 - L
English-19SETUP AND ADJUSTMENTSTiresMount rear drive wheels using the lug nuts installed on the hubs.Check the tire pressure in all four tires. All ti
©2008 HTC. All rights reserved.Beatrice, NE. Printed in U.S.A.
English-20SETUP AND ADJUSTMENTSCutting Height1. Stop the mower and disengage the blades.2. Raise the deck height lever to the transport position.3.
English-21SETUP AND ADJUSTMENTSMotion Control Linkage AdjustmentAdjustment must be made with the rear wheels rotating. Raise the rear of the machine a
CONTROLSEnglish-22This operator’s manual describes the Yazoo/Kees Zero Turn Rider. The rider is tted with a Kawasaki or Kohler four-stroke V-Twin en
CONTROLSEnglish-23Motion Control LeversThe machine’s speed and direction are continuously variable using the two steering controls. The steering contr
CONTROLSEnglish-24TrackingIf the mower is not tracking straight, check the air pressure in both rear tires. Recommended air pressure is 15 psi (1 bar)
CONTROLSEnglish-25RefuelingThe machine has two fuel tanks, one on each side just behind the seat. The tank capacity is 5.7 gallons (17 liters).The eng
CONTROLSEnglish-26Ignition SwitchThe ignition switch is placed on the driver’s control panel and is used to start and stop the engine.8050-140Hour met
CONTROLSEnglish-27Throttle ControlThe throttle control regulates the engine speed and thereby the rate of rotation of the blades, assuming the blade s
CONTROLSEnglish-28Mower Deck Cut Height Lift LeverThe lifting lever is used to place the mower deck in the transport position or one of the 14 differe
English-29OPERATIONRead “Safety Instructions” section and following pages, if you are unfamiliar with the machine.TrainingZero turn mowers are far mor
INTRODUCTION ...5General ...
English-30OPERATIONBefore StartingRead the sections on Safety Instructions and • Controls before starting the machine.Perform the daily maintenance be
English-31OPERATIONMove the steering controls outward to the • locked (outer) neutral position. Move the throttle to the middle position.• If the engi
English-32OPERATIONWeak batteryIf your battery is too weak to start the engine, it should be recharged. (See “Battery” in the Maintenance Section.)If
English-33OPERATION8011-788Move steering controls to neutral and set cutting height.RunningRelease the parking brake by moving the lever 1. downward.
English-34OPERATIONOperating on hillsRead the Safety Instructions “Driving on Slopes” in the “Safety Instructions”.8011-640Stopping conditions WARNI
English-35OPERATIONMowing Tips Observe and ag rocks and other xed objects • to avoid collisions.Begin with a high cutting height and reduce it • unt
English-36OPERATIONStopping the EngineAllow the engine to idle a minute in order to attain normal operating temperature before stopping it, if it has
English-37OPERATIONMoving ManuallyWhen pushing or pulling the mower, be sure to open the release valves on both hydraulic pumps.Always turn off engine
English-38MAINTENANCEAnnual inspection and maintenance from an authorized Yazoo/Kees dealer is recommended to keep your machine in the best condition
English-39MAINTENANCEHydraulic systemCheck oil level in tank daily. Oil level should be ¾" to 1" below the top of the tank. Check all tting
English-40MAINTENANCECutter HousingsGrease housings once weekly or every 40 to 50 hours of use. Use a good synthetic grease. Pump grease in until a sm
English-41MAINTENANCELubricationSee service decal under foot plate for service points and maintenance intervals. Clean grease zerks thoroughly before
English-42MAINTENANCEAdjusting the Mower DeckLevelingPosition the mower on a level, preferably 1. concrete, surface.Check the pressure in all four tir
English-43MAINTENANCECaster WheelsCheck every 200 hours. Lift front of unit off of ground so caster wheels can rotate freely. Tighten caster bolt (34)
English-44LUBRICATIONGeneralRemove the ignition key to prevent unintentional movements during lubrication.When lubricating with an oil can, it must be
English-45LUBRICATIONLubricating the CablesIf possible, grease both ends of the cables and move the controls to end stop positions when lubricating. R
English-46LUBRICATIONDeck belt pulleysLubricate with a grease gun, two strokes.Mower Deck Height AdjusterLubricate using a grease gun, one zerk, until
English-47LUBRICATIONMower Deck StrutsLubricate with a grease gun, one zerk for each strut, until the grease is forced out.Use only good quality molyb
English-48TROUBLE SHOOTINGProblemCauseThe engine will not start.Blade switch is engaged.• Steering controls are not locked in the neutral position.• D
English-49TROUBLE SHOOTINGUneven mowing results.Different air pressure in the tires on the left and right sides.• Bent blades.• The suspending for the
English-5INTRODUCTIONCongratulationsThank you for purchasing a Yazoo/Kees ride-on mower. This machine is built for superior efciency to rapidly mow p
STORAGEEnglish-50Winter StorageAt the end of the mowing season, the machine should be readied for storage (or if it will not be in use for longer than
English-51CONFORMITY CERTIFICATESConformity CerticatesUSA requirementsLabels are placed on the engine and/or in the engine compartment stating that t
EngineManufacturer Type PowerLubricationOil capacity excluding lterOil capacity including lterEngine oil (See viscosity diagram)FuelFuel tank capaci
Cutting WidthCutting HeightUncut CircleNumber of BladesBlade LengthAnti=Scalp RollersSprung SeatHinged Arm RestsHour MeterBlade EngagementDeck Constru
EngineManufacturer Type PowerLubricationOil capacity excluding lterOil capacity including lterEngine oil (See viscosity diagram)FuelFuel tank capaci
Cutting WidthCutting HeightUncut CircleNumber of BladesBlade LengthAnti=Scalp RollersSprung SeatHinged Arm RestsHour MeterBlade EngagementDeck Constru
EngineManufacturer Type PowerLubricationOil capacity excluding lterOil capacity including lterEngine oil (See viscosity diagram)FuelFuel tank capaci
Cutting WidthCutting HeightUncut CircleNumber of BladesBlade LengthAnti=Scalp RollersSprung SeatHinged Arm RestsHour MeterBlade EngagementDeck Constru
TECHNICAL DATAEnglish-58AccessoriesBioClip attachment (Mulch clip)Front Bafe KitFoot-operated Mower Deck LiftHead lightsRollover Protection System
SERVICE JOURNALEnglish-59ActionDate, mtr reading, stamp, signDelivery ServiceCharge the battery.1. Mount the rear wheels.2. Adjust the tire pressure o
English-6INTRODUCTIONGood ServiceYazoo/Kees’s products are sold only in specialized retail stores with complete service. This ensures that you as a cu
SERVICE JOURNALEnglish-60After the First 5-8 Hours1. Change engine oil.ActionDate, mtr reading, stamp, sign
SERVICE JOURNALEnglish-61Action Date, mtr reading, stamp, sign25-Hour Service1. Check the fuel pump’s air lter.2. Check the hydraulic system’s oil
SERVICE JOURNALEnglish-62Action Date, mtr reading, stamp, sign50-Hour Service1. Perform the 25-hour service.2. Lubricate the front wheel bearings.3.
SERVICE JOURNALEnglish-63Action Date, mtr reading, stamp, sign100-Hour Service1. Perform the 25-hour service.2. Perform the 50-hour service.3. Chan
SERVICE JOURNALEnglish-64Action Date, mtr reading, stamp, sign300-Hour Service1. Inspect the machine. Come to agreement with the customer as to w
SERVICE JOURNALEnglish-65Action Date, mtr reading, stamp, signAt Least Once Each Year1. Clean the engine’s cooling air intake (25 hours).2. Replace
SERVICE JOURNALEnglish-66ActionDate, mtr reading, stamp, sign
P/N 539 131257 R02 03/18/08
English-7SYMBOLS AND DECALSThese symbols are found on the machine and in the operator’s manual.Study them carefully so that you know what they mean.
English-8SYMBOLS AND DECALS Read Shut off engine and Keep a safe Use on slopes No passengers Operator’s remove key before distance from no gr
English-9SAFETYThese instructions are for your safety. Read them carefully.IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND
Commentaires sur ces manuels